Which command can be used to verify the switch routing table?

Use the show ip route EXEC command to display the current state of the routing table.

1. What commands can be used to verify the routing protocol being used?
2. Which command is used to find the routing table?
3. What is the command to check routing table in Linux?
4. What command s would you use to verify that there is a routing table used to route IPv4 and IPv6 packets between the three sections?
5. How do you verify a routing table?
6. What command is used to verify condition of the switch interfaces?
7. How to use traceroute command in Linux?
8. Which command is used to verify the contents of the VRF routing table?
9. What is the command to verify the RIP routing?
10. Which commands can be used for routing related information?
11. What is the command to verify the RIP routing?
12. What command can be used to verify the status of a router interface?
13. What command do you use to verify network settings?
14. What is tracert command used for?
15. What are the 3 types of routing protocols?
16. How do I use route command?
17. Which command is used to verify the contents of the VRF routing table?
18. What command enables RIPv1?
19. Which command enables RIP routing protocol in a router?

What commands can be used to verify the routing protocol being used?

The show ip protocols command is used when a dynamic routing protocol is being run on the device. The output from this command can be used to verify that the routing protocol configuration is being processed as expected. The exact output from this command depends on the dynamic routing protocol that is configured.

Which command is used to find the routing table?

You can display the routing table using the netstat -rn command or the route -s command.

What is the command to check routing table in Linux?

The “ip route” command in Linux is used to view and modify the routing table. Using this command, you can add new routes to a particular network or host. You can delete the routes if you no longer want them in your routing table.

What command s would you use to verify that there is a routing table used to route IPv4 and IPv6 packets between the three sections?

The ping command for IPv6 is identical to the command used with IPv4 except that an IPv6 address is used. As shown in Figure 1-23, the ping command is used to verify Layer 3 connectivity between R1 and PC1. Other useful IPv6 verification commands include: show interface.

How do you verify a routing table?

# netstat -r

Make sure a routing table entry exists for each possible destination network. In particular, PPP devices, listed under Interface , should be matched with the appropriate host names listed under Gateway . The Gateway entry should, in turn, be matched with the correct entry under Destination .

What command is used to verify condition of the switch interfaces?

Run the show ip interface brief command to verify connected interfaces are up, and IP addresses are configured correctly.

How to use traceroute command in Linux?

To perform a trace route in Linux open Terminal and type in “traceroute domain.com” replacing domain.com with your domain name or IP address. If you do not have trace route installed you may need to install it. For example in Ubuntu the command to install trace route is “sudo apt-get install traceroute”.

Which command is used to verify the contents of the VRF routing table?

Verify Route Leaking Configuration

To view the FRR IP routing table, use the NCLU net show route vrf <vrf-name> command or the vtysh show ip route vrf <vrf-name> command. These commands show all routes, including routes leaked from other VRFs.

What is the command to verify the RIP routing?

To see a listing of the RIP routes in the switch's routing table, use the show ip rip database command. (You can also display similar information using the RIP option in the show ip route command.) This command displays all active rip routes.

Which commands can be used for routing related information?

The netstat -r command displays the current routing information contained in the routing tables. Note: You must use the same set of commands (route, smitty, ifconfig and chdev commands) for creating or deleting the routing table.

What is the command to verify the RIP routing?

To see a listing of the RIP routes in the switch's routing table, use the show ip rip database command. (You can also display similar information using the RIP option in the show ip route command.) This command displays all active rip routes.

What command can be used to verify the status of a router interface?

The most useful of these is the show ip interface brief command. You can verify connectivity from the interface using the ping command.

What command do you use to verify network settings?

The ipconfig command displays the basic IP addressing information for each network interface on the Windows system. This information includes both the IP address and subnet mask.

What is tracert command used for?

This article describes TRACERT (Trace Route), a command-line utility that you can use to trace the path that an Internet Protocol (IP) packet takes to its destination.

What are the 3 types of routing protocols?

Routing Information Protocol (RIP) Interior Gateway Protocol (IGRP) Open Shortest Path First (OSPF)

How do I use route command?

The -f option clears the routing tables of all gateway entries. If you use the -f option in conjunction with one of the commands, the tables are cleared before you run the command. By default, routes are not preserved when you restart the system. Use the -p option with the add command to make a route persistent.

Which command is used to verify the contents of the VRF routing table?

Verify Route Leaking Configuration

To view the FRR IP routing table, use the NCLU net show route vrf <vrf-name> command or the vtysh show ip route vrf <vrf-name> command. These commands show all routes, including routes leaked from other VRFs.

What command enables RIPv1?

To enable RIP routing on a router, issue the router rip command in global configuration mode. To specify a list of networks for the RIP routing process, issue the network command in router configuration mode. By default, RIP enabled routers run RIP v1.

Which command enables RIP routing protocol in a router?

Using the Cisco IOS, the command to enable RIP routing protocol is router rip. The version command is used to specify which RIP version to use (either 1 or 2). If the version command is omitted then the router defaults to sending RIPv1 but can receive both RIPv1 and RIPv2.